Email us
Info@nernstcatering.com
In 2003, we established a partnership with the Italian ice cream equipment company Carpigiani, which allowed us to gain a deep understanding of the requirements for the production and sale of gelato; subsequently, we began designing and manufacturing display cases for gelato.
Read More
In coastal environments characterized by high salt mist and humidity, the primary goal of commercial refrigeration maintenance is to prevent salt scale caking and eliminate the formation of electrochemical corrosion media. Power Disconnection & Safety Warning Before performing any cleaning of the compressor compartment, inspecting the chassis, or servicing electrical components, always disconnect the power plug or switch off the dedicated circuit breaker. Never spray water directly into the compressor compartment, electrical control boxes, or fan motors with a high-pressure washer to prevent short circuits and electrical shock. Standard Operating Procedure for Coastal Refrigeration Maintenance 1. Bi-Weekly: Clean the Condenser and Aluminum Fins Grease vapor mixed with airborne salt mist readily forms a dense, corrosive crust on condenser coils. Procedure: Apply a neutral coil cleaner and gently comb through the fins along their vertical grain using a soft-bristle brush. Rinse thoroughly using clean, warm water from a low-pressure spray bottle. Verification: Inspect the gaps between fins against a backlight to ensure no sludge, white salt residue, or green patina remains. After startup, ensure the compressor discharge line warms up evenly without tripping high-pressure safety cut-outs. 2. Daily at Closing or Weekly: Wipe Down Stainless Steel Surfaces and Seams Chloride ions in the air continuously attack the passive protective layer of stainless steel. Procedure: Wipe the exterior body, rear panels, and joint seams with warm water and a neutral detergent (never use chlorine-based bleach or strong acidic/alkaline cleaners). Dry completely with a clean towel, then apply a thin coat of food-grade stainless steel protective polish. Verification: Surface shows no dullness, white spotting, or yellowish-brown pitting corrosion, with no granular salt texture felt by hand. 3. Weekly: Clean Door Gaskets and Condensate Drain Channels Saline moisture tends to collect in gasket folds and around heated door frames, accelerating gasket embrittlement and cracking. Procedure: Peel back the folds of the PVC door gaskets and clean out mildew and salt deposits with a damp cloth soaked in warm water. Clear the internal and external defrost drain holes and empty the evaporation pan to eliminate standing water. Verification: Place a banknote between the door gasket and frame and close the door; if the note resists being pulled out and does not slide freely, the magnetic seal integrity is adequate. 4. Monthly: Protect Electrical Controls and Mechanical Hardware Salt air causes contact resistance and mechanical binding on exposed fittings. Procedure: Inspect the digital thermostat housing, compressor terminal junction box, leveling feet, and door hinges. Blow away loose dust and moisture from electrical terminals with dry compressed air. Lubricate hinge pivot pins, latch mechanisms, and leveling screws with food-grade grease or anti-rust wax. Verification: Doors swing smoothly without squeaking or metal grinding; electrical terminals show no green copper corrosion (verdigris) or black heat-oxidation marks. Key Maintenance Precautions and Environmental Control Strictly Avoid Chlorine-Based Cleaners: Disinfectants containing sodium hypochlorite, hypochlorous acid, or acidic hand soaps release free chloride ions that cause severe pitting, pinhole leaks, and irreversible staining on 201 and 304 stainless steel within days. Never Use Abrasive Metal Tools: Do not scrub internal liners or condenser coils with steel wool or rigid scrapers; scratching the surface passivation film or protective coating accelerates core metal corrosion. Airflow and Unit Placement: Keep the condenser air intake away from open coastal windows and raw seafood prep sinks. Maintain a clearance of at least 15–20 cm around the cabinet to ensure adequate heat dissipation and prevent moist air recirculation around the condensing unit.
Read More
Commercial refrigerators have a significantly higher failure rate in coastal areas due to the compounding effects of heavy salt spray corrosion, high relative humidity, and sustained high-temperature, high-load operating conditions. These environmental factors progressively degrade the refrigeration circuit, electrical controls, insulation structure, and metal cabinetry. 1. Electrochemical Salt Spray Corrosion: The Primary Cause of Refrigerant Leaks Coastal ambient air contains high concentrations of airborne sodium chloride ($NaCl$) particles. Chloride ions have an extremely small ionic radius, allowing them to penetrate protective passive films on metal surfaces and initiate severe localized corrosion: Pitting and Galvanic Breakdown of Condenser Aluminum Fins: Most commercial refrigerators use copper-tube, aluminum-fin condensers. Copper and aluminum have a large electrochemical potential difference. In humid, salt-laden moisture films, galvanic corrosion occurs rapidly. The aluminum acts as a sacrificial anode and disintegrates, causing the fins to crumble away. Subsequently, the exposed copper tubes suffer pitting and stress corrosion cracking, leading to refrigerant leakage (pinhole or capillary leaks). Brazed Joint Failure: Pipe connections around the compressor discharge and suction lines are typically brazed using copper-phosphorus or silver alloys. Under salt-spray catalytic action, micro-pores in brazed joints oxidize, corrode, and peel apart, dumping the refrigerant charge and eventually causing compressor seizure from oil starvation. 2. High Moisture and Salt Deposition: Electrical Shorts and Component Failures Relative humidity in coastal regions consistently hovers between 75% and 95% or higher. Combined with airborne ionic salts, this severely impacts electrical systems: PCB and Sensor Short Circuits: Salt spray settling on printed circuit boards absorbs moisture from the air, forming a conductive electrolyte layer. This causes a sharp drop in insulation resistance, electrical arcing, short circuits, or outright component burnouts. In addition, corroded terminals on temperature sensors and defrost probes drift in resistance value, triggering false defrost cycles or non-stop running. Burnt Starting Relays and Contactors: Run/start capacitors, AC contactors, and PTC relays corrode and oxidize easily in humid, salty air. Increased contact resistance leads to overheating, pitted contacts, welding, or starting failures in the compressor. Corroded Fan Motors: Both evaporator and condenser fan motors run continuously. Humid coastal air causes the bearings and motor stators to rust, seize, or burn out from overheating, which instantly triggers poor heat exchange and high-pressure trips. 3. High Thermal and Latent Moisture Loads: Compressor Overload and Insulation Breakdown Coastal tropical or subtropical maritime weather introduces massive thermal and latent moisture loads: Restricted Condensation and High-Pressure Cutoffs: Once the condenser fins disintegrate or become fouled with salt crust and airborne grease, heat rejection plummets. Compressor discharge pressures and temperatures spike, forcing the unit to run in chronic overload conditions. This degrades and carbonizes the compressor oil, burning out windings over time. Heavy Frost and Condensation from Frequent Door Openings: Hot, humid air rushes into the cabinet each time doors open. Moisture condenses instantly on evaporator coils to build dense frost layers, blocking airflow. This drops evaporation pressure, risks liquid floodback (slugging the compressor), and spikes electric defrost cycles and power consumption. Degraded Gaskets and Insulation: Intense UV exposure and high humidity accelerate the hardening, cracking, and deformation of PVC magnetic gaskets, breaking the door seal. If water vapor penetrates the polyurethane cabinet insulation, moisture hydrolysis destroys the closed-cell foam, causing insulation performance to degrade permanently. 4. Exterior Cabinet Corrosion: Rapid Degradation of 201 Stainless Steel Many economy-grade commercial cabinets utilize 201 stainless steel (high manganese, low nickel content). While serviceable in dry inland environments, 201 fails quickly under marine conditions: Surface pitting and dense, yellowish-brown rust spots develop quickly. Door hinges, leveling legs, and cracks in vinyl-coated wire shelves rust or break, leading to door sagging, poor sealing, severe cold air loss, and spiked power usage. Recommended Specifications for Marine & Coastal Environments We have developed products specifically for coastal/high-salinity regions. Critical Component Standard Inland Spec Coastal / High Salt-Spray Spec Key Benefits Condenser / Evaporator Standard hydrophilic aluminum fins + copper tubes Epoxy Gold Fin / Electrophoretic (E-coat) black coating / Pure copper micro-channel Seals against salt moisture films; passes 1,000+ hour salt-spray tests; prevents refrigerant leaks Control Board (PCB) Bare board / minimal conformal coating Full conformal coating (anti-moisture, anti-salt-spray, anti-mildew) or potted waterproof box Blocks conductive water film formation; prevents circuit shorts and board burnouts Cabinet Body & Interior 201 stainless steel / powder-coated galvanized steel Food-grade 304 stainless steel (resistant to chloride pitting) Long-term resistance to salt corrosion; rust-free, hygienic, and easy to clean Hardware & Fans Galvanized steel hinges / stamped steel axial fans Heavy-duty 304 stainless steel hinges / IP55+ sealed waterproof/corrosion-proof EC fans Prevents door sag and prevents motor burnout from water ingress Gaskets & Glass Standard double-pane glass Heated Low-E anti-condensation glass + widened heavy-duty anti-aging magnetic gaskets Eliminates door sweating/water puddling and minimizes thermal leakage
Read MoreScan to Whatsapp :
Scan to wechat :